Original Industrial Spare Part

Mitsubishi FT-600DHVP-P-S Retrofit Controller for Legacy Systems

Verify the part, confirm the platform family, and move straight into quotation with the right commercial details.

SKU: FT-600D(HVP P.S) FTI-600D-T6 USAHEM-02-TE53 2706-LV2R PLC & Industrial Automation Modules Mitsubishi

RFQ Ready

Pricing by RFQ

How Buyers Usually Use This Page

  • Confirm the exact part number and platform family before sending the quote request.
  • Use direct email when quantity, condition, and destination are already defined internally.
  • Switch to the broader brand or category archive when you need alternates nearby.

Series Navigation

Move through the most common platform families behind this part.

Mitsubishi FT-600DHVP-P-S Retrofit Controller for Legacy Systems: Seamless Compatibility and Smooth Upgrade for Aging Turbomolecular Pump Platforms

The Mitsubishi FT-600DHVP-P-S is a retrofit-compatible turbomolecular pump controller designed to serve as a direct replacement for discontinued and end-of-life vacuum pump control units in legacy automation environments. Originally paired with the FTI-600D-T6 turbomolecular pump drive assembly, this controller has become a critical spare part for semiconductor fabrication, thin-film deposition, analytical instrumentation, and industrial vacuum process lines where the original equipment manufacturer no longer provides active support. With verified SKU compatibility across the USAHEM-02, TE53-2706, and LV2R interface platforms, the FT-600DHVP-P-S enables engineers to extend the operational life of existing vacuum systems without committing to a full platform replacement.

NINERMAS maintains reserved inventory of the FT-600DHVP-P-S to support customers facing urgent replacement needs, long OEM lead times, or end-of-support notifications. Each unit undergoes pre-shipment functional testing and ships with a 12-month warranty covering manufacturing defects and operational failures under normal service conditions.

Upgrade Compatibility Table

Parameter FT-600DHVP-P-S (This Unit) Retrofit Notes
Primary SKU FT-600DHVP-P-S Verify label against FTI-600D-T6 drive assembly
Compatible Drive FTI-600D-T6 Confirm connector pinout before installation
Interface Compatibility USAHEM-02, TE53-2706, LV2R Check firmware revision on host controller
Communication Protocol RS-232 / RS-485 (model-dependent) Verify baud rate and parity settings in PLC program
Power Supply Input Single-phase AC, 200–240 V Confirm panel power capacity before wiring
Mounting Format Panel-mount / DIN rail adapter available Measure cabinet depth and clearance for cooling
Installation Space Standard 19-inch rack or control cabinet Confirm vertical clearance for cable routing
Warranty 12 Months Covers manufacturing defects under normal operation
Pre-Shipment Test Yes — functional run test performed Test report available on request
Replacement Path Direct drop-in for legacy HVP P.S. series No firmware modification required in most cases

Retrofit Planning for Existing Automation Systems

Replacing the FT-600DHVP-P-S in an active vacuum process line requires careful coordination across multiple subsystems. Engineers should begin by auditing the existing control cabinet layout to confirm available space, terminal block assignments, and cable routing paths before removing the legacy unit. The FTI-600D-T6 turbomolecular pump drive must be electrically isolated prior to controller removal, and the interlock chain connecting the pump drive to the process chamber safety circuit should be documented to avoid inadvertent process faults during the swap.

On the communication side, the USAHEM-02 interface module handles the serial link between the pump controller and the host PLC or SCADA system. Before disconnecting the legacy FT-600DHVP-P-S, technicians should capture the current RS-232 or RS-485 configuration parameters — baud rate, data bits, stop bits, and parity — from the existing PLC program or HMI configuration screen. The TE53-2706 signal conditioning board, if present in the same cabinet, may also require re-addressing after the controller swap to maintain correct I/O mapping.

The LV2R relay output module connected to the pump controller typically handles interlock signals for roughing pump sequencing and vent valve control. Verify that the relay output wiring from the FT-600DHVP-P-S matches the terminal designations on the LV2R before energizing the replacement unit. Mismatched relay polarity is a common source of commissioning delays in turbomolecular pump retrofits.

For systems using a Mitsubishi MELSEC Q-series or iQ-R series PLC as the host controller, the pump controller communication parameters are typically stored in a dedicated function block or structured text routine. Retrieve a backup of the PLC program before beginning the retrofit, and confirm that the communication module — such as a QJ71C24N or RJ71C24 serial communication unit — is configured to match the FT-600DHVP-P-S default settings. If the HMI screen references pump status tags derived from the serial link, those tag addresses should be verified against the replacement controller’s register map to prevent display errors after restart.

Power supply capacity is another critical checkpoint. The FT-600DHVP-P-S draws from the panel’s single-phase AC bus, and the existing power supply module — often a Mitsubishi Q61P or equivalent — should be confirmed to have sufficient headroom for the replacement unit’s inrush current. If the cabinet also houses additional I/O modules, a backplane power audit is recommended before commissioning.

Where the original system used a dedicated programming cable for initial setup or parameter backup, ensure the correct cable type is available for the FT-600DHVP-P-S. Some legacy Mitsubishi pump controllers use proprietary connector formats that differ from standard USB-to-serial adapters. NINERMAS can advise on compatible programming cable options based on the specific firmware version of the unit supplied.

Downtime Control During System Migration

Minimizing unplanned downtime during a turbomolecular pump controller replacement is essential in semiconductor, analytical, and industrial vacuum environments where process continuity directly affects yield and throughput. The recommended approach is to pre-stage the FT-600DHVP-P-S alongside the existing system, verify all wiring diagrams and communication parameters in advance, and schedule the physical swap during a planned maintenance window.

Before powering down the legacy controller, export or photograph all parameter settings accessible through the front panel or serial interface. This includes acceleration ramp profiles, speed setpoints, interlock thresholds, and any custom alarm configurations. Preserving the original program logic ensures that the replacement unit can be commissioned to match the existing process recipe without requiring a full re-qualification cycle.

During the physical swap, label all terminal connections before disconnection and use a structured re-wiring checklist to confirm each wire is returned to the correct terminal on the FT-600DHVP-P-S. After wiring is complete, perform a low-speed functional test before ramping the turbomolecular pump to full operating speed. Monitor the communication link between the replacement controller and the host PLC or SCADA system to confirm that status signals, fault codes, and speed feedback are being received correctly.

For sites with strict change control requirements, NINERMAS can provide documentation supporting the retrofit qualification process, including the pre-shipment test record and unit-level traceability information.

Retrofit Support FAQ

Q1: Is the FT-600DHVP-P-S a direct replacement for the FTI-600D-T6 power supply assembly?
The FT-600DHVP-P-S is the high-voltage power supply section of the FTI-600D-T6 turbomolecular pump drive system. It is designed as a direct retrofit replacement for the HVP P.S. module within that drive assembly. Confirm the connector pinout and firmware revision on the host drive before installation to ensure full compatibility.

Q2: What communication interfaces does the FT-600DHVP-P-S support, and how do I verify compatibility with my existing PLC?
The unit supports RS-232 and RS-485 serial communication depending on the specific configuration. Retrieve the baud rate, parity, and data bit settings from your existing PLC program or HMI configuration before replacing the legacy controller. The USAHEM-02 interface module and TE53-2706 signal board in your cabinet may also require parameter verification after the swap.

Q3: Does NINERMAS perform pre-shipment testing on the FT-600DHVP-P-S?
Yes. Every FT-600DHVP-P-S unit supplied by NINERMAS undergoes a functional run test prior to shipment. A test record is available on request. The unit ships with a 12-month warranty covering manufacturing defects and operational failures under normal service conditions.

Q4: What is the typical lead time, and does NINERMAS maintain stock?
NINERMAS maintains reserved inventory of the FT-600DHVP-P-S to support urgent replacement requirements and reduce exposure to OEM lead time uncertainty. Contact our team for current stock status and delivery timeline confirmation before placing your order.

Product Series

Legacy

Country of Origin

JP

Catalog Continuation

More Mitsubishi modules in the catalog.

Use the brand lane to compare nearby part numbers, platform-adjacent modules, and other inquiry-ready listings before sending your final RFQ.

Open this lane

Catalog Continuation

Alternative parts within PLC & Industrial Automation Modules.

Stay inside the same system family when you need substitutes, adjacent modules, or a broader shortlist for procurement review.

Open this lane

Industrial RFQ Support

Need a fast quote for a specific part number or system family?

Send your inquiry with brand, series, quantity, condition, and destination details. We will follow up on availability, lead time, and shipping options.

CallPhone MailEmail WAChat TopBack