Original Industrial Spare Part

Pepperl+Fuchs NJ4-12GM-N-10M Service-Ready Spare Part

Verify the part, confirm the platform family, and move straight into quotation with the right commercial details.

SKU: NJ4-12GM-N-10M TSI & Rotating Machinery Monitoring Pepperl+Fuchs

RFQ Ready

Pricing by RFQ

How Buyers Usually Use This Page

  • Confirm the exact part number and platform family before sending the quote request.
  • Use direct email when quantity, condition, and destination are already defined internally.
  • Switch to the broader brand or category archive when you need alternates nearby.

Series Navigation

Move through the most common platform families behind this part.

Pepperl+Fuchs NJ4-12GM-N-10M Service-Ready Spare Part for Industrial Maintenance

The Pepperl+Fuchs NJ4-12GM-N-10M is an original inductive proximity sensor from the NJ Series, engineered for reliable detection in demanding industrial environments. With a 4 mm sensing range, M12 threaded barrel housing, and a 10-meter pre-wired cable, this sensor is a direct service-ready replacement for aging or failed units in automated production lines, conveyor systems, machine tool applications, and process control installations. Sourced as an original Pepperl+Fuchs component, the NJ4-12GM-N-10M is fully compatible with existing NJ Series mounting hardware and wiring infrastructure, enabling rapid field replacement without system reconfiguration.

For maintenance engineers managing legacy automation systems, the NJ4-12GM-N-10M represents a low-risk, high-confidence spare part choice. Its standardized M12 form factor and PNP normally-open output configuration align with the majority of PLC input modules deployed across Siemens S7, Allen-Bradley CompactLogix, Mitsubishi MELSEC, and Omron CJ/NJ series controllers. Procurement engineers can stock this sensor with confidence, knowing that its electrical and mechanical specifications are unchanged from the original factory build, eliminating compatibility verification delays during emergency maintenance windows.

Spare Maintenance Table

Parameter Specification
SKU / Part Number NJ4-12GM-N-10M
Brand Pepperl+Fuchs
Series NJ Series Inductive Proximity Sensors
Sensing Range 4 mm (nominal)
Housing M12 x 1, Threaded Barrel, Stainless Steel
Output Type PNP, Normally Open (NO)
Cable Length 10 m, Pre-wired PVC Cable
Supply Voltage 10–30 V DC
Output Current ≤ 200 mA
Protection Rating IP67
Operating Temperature -25°C to +70°C
Switching Frequency ≤ 3000 Hz
Connection Type Pre-wired, 3-wire
Compatibility Direct replacement for NJ4-12GM-N series; compatible with standard PLC digital input modules
Country of Origin Germany
Warranty 12 Months from date of shipment
Condition Original, New-in-Box
Application Position detection, end-of-travel sensing, conveyor indexing, machine tool guarding

Maintenance Planning for Continuous Operation

When replacing the NJ4-12GM-N-10M in the field, a disciplined maintenance engineer will treat the sensor swap as an opportunity to audit the surrounding electrical circuit and control architecture. The 10-meter pre-wired cable terminates at a field junction box or directly at a PLC input terminal, and both the cable routing and terminal block condition should be inspected during replacement. Corroded or loose connections on Phoenix Contact or Weidmüller terminal blocks are a common secondary fault that can cause intermittent input signals even after a new sensor is installed.

The PLC digital input card receiving the NJ4-12GM-N-10M signal should be verified for correct input voltage range and current sink capacity. On Siemens S7-300 or S7-400 systems, the SM 321 digital input module is a frequent companion component; on Allen-Bradley platforms, the 1769-IQ16 or 1734-IB8 POINT I/O input modules serve the same role. If the sensor is part of a safety-rated detection circuit, the safety relay module — such as a Pilz PNOZ or Schmersal SRB series unit — should also be tested for correct response time and reset behavior.

Power supply stability is critical for inductive sensor reliability. The 24 V DC rail feeding the NJ4-12GM-N-10M should be checked with a multimeter or power quality analyzer; ripple exceeding 5% can cause false triggering or reduced sensing range. MEAN WELL SDR-series or Phoenix Contact QUINT-series DIN-rail power supplies are commonly used in the same control cabinet and should be included in the annual inspection checklist. Surge protection devices on the 24 V bus, such as Phoenix Contact TT-UKK5-D/24DC/FM surge arresters, protect sensor circuits from transient damage and should be replaced on a 5-year cycle or after any lightning event.

For systems using Profibus DP or Profinet IO fieldbus architectures, the sensor’s host I/O block or remote I/O station — such as a Pepperl+Fuchs ICE1 or Turck BL20 module — should be inspected for firmware currency and connector integrity. A failed or degraded remote I/O gateway can mask sensor faults or generate spurious alarms, complicating fault isolation. Similarly, if the NJ4-12GM-N-10M feeds into a Siemens ET 200SP or ET 200M distributed I/O station, the backplane bus connector and module seating should be verified during the replacement procedure.

Stocking a minimum of two NJ4-12GM-N-10M units per production line is recommended for facilities operating continuous or three-shift schedules. Pairing this sensor stock with spare terminal blocks, cable glands, and a roll of 0.75 mm² control cable ensures that a complete field repair can be executed within a single maintenance window without waiting for additional parts procurement.

Site Replacement Workflow

Step 1 — Isolation and Lockout/Tagout: De-energize the machine circuit feeding the NJ4-12GM-N-10M. Apply LOTO per site procedure. Confirm zero-energy state with a calibrated voltage tester before touching any wiring.

Step 2 — Document Existing Installation: Photograph the sensor mounting position, cable routing, and terminal connections. Note the sensing gap distance from the target surface and the mounting torque specification (typically 15–20 Nm for M12 sensors).

Step 3 — Remove Failed Unit: Disconnect the pre-wired cable at the terminal block or junction box. Unscrew the sensor from its mounting bracket using a 17 mm open-end wrench. Inspect the mounting thread for damage or corrosion.

Step 4 — Install NJ4-12GM-N-10M Replacement: Thread the new sensor into the mounting bracket by hand, then torque to specification. Route the 10-meter cable along the original cable tray path, securing with cable ties at 300 mm intervals. Reconnect at the terminal block, observing the original wire color coding (Brown = +24V, Blue = 0V, Black = Output).

Step 5 — Functional Verification: Re-energize the circuit. Use the sensor’s LED indicator to confirm power-on status. Introduce a ferrous metal target at the rated sensing distance and verify output switching at the PLC HMI or with a handheld signal tester. Confirm the PLC program registers the correct input state.

Step 6 — Documentation and Spare Stock Update: Record the replacement in the CMMS (Computerized Maintenance Management System) with date, technician ID, and new sensor serial number. Update the spare parts inventory to trigger a reorder for the consumed unit.

This workflow is applicable to all NJ Series M12 inductive sensors and can be adapted for similar Pepperl+Fuchs NBB, NCB, or NMB series sensors sharing the same housing format and electrical interface.

Spare Parts Support FAQ

Q1: Is the NJ4-12GM-N-10M a direct drop-in replacement for older NJ Series units without wiring changes?
Yes. The NJ4-12GM-N-10M maintains the same M12 threaded housing, PNP NO output configuration, and 3-wire pre-wired cable interface as previous NJ Series production runs. No wiring diagram changes or PLC parameter adjustments are required for a like-for-like replacement. Confirm the sensing range setting on the target machine matches the 4 mm nominal range before closing the maintenance work order.

Q2: How is the NJ4-12GM-N-10M tested before shipment?
Each unit undergoes electrical continuity verification, output switching function test, and insulation resistance check prior to packaging. Sensors are shipped in original Pepperl+Fuchs anti-static packaging with factory labels intact. A test report is available upon request for quality-critical applications.

Q3: What is the recommended spare parts stocking strategy for this sensor?
For production facilities with more than five NJ4-12GM-N-10M units installed, a minimum buffer stock of 10–15% of the installed base is recommended, with a reorder point triggered when stock falls below two units. For single-line installations, maintaining one spare unit on-site and one at the regional warehouse provides adequate coverage for emergency response within a four-hour maintenance window.

Q4: What warranty and long-term supply commitment applies to this part?
All NJ4-12GM-N-10M units supplied by NINERMAS carry a 12-month warranty covering manufacturing defects and premature failure under normal operating conditions. NINERMAS maintains a long-term supply commitment for NJ Series sensors, including end-of-life and discontinued variants, supporting customers through system lifecycle extensions and legacy equipment maintenance programs. Contact our technical team for multi-year supply agreements and consignment stock arrangements.

Product Series

Other series

Country of Origin

DE

Catalog Continuation

More Pepperl+Fuchs modules in the catalog.

Use the brand lane to compare nearby part numbers, platform-adjacent modules, and other inquiry-ready listings before sending your final RFQ.

Open this lane

Catalog Continuation

Alternative parts within TSI & Rotating Machinery Monitoring.

Stay inside the same system family when you need substitutes, adjacent modules, or a broader shortlist for procurement review.

Open this lane

Industrial RFQ Support

Need a fast quote for a specific part number or system family?

Send your inquiry with brand, series, quantity, condition, and destination details. We will follow up on availability, lead time, and shipping options.

CallPhone MailEmail WAChat TopBack